logo
บ้าน
สินค้า
เกี่ยวกับเรา
ทัวร์โรงงาน
ควบคุมคุณภาพ
ติดต่อเรา
ขออ้าง
ข่าว
TOGETHER HTL LTD
บ้าน ข่าว

A Complete Guide to Roller Runout on BOPP, BOPET and Cast Film Lines

ผลิตภัณฑ์ทั้งหมด
บริษัท ทีโอจีอีเธอร์ เอชทีแอล จำกัด เป็นบริษัทที่ดีมาก ฉันยินดีที่จะร่วมงานกับคุณ ปลอดภัย มีประสิทธิภาพ เป็นมืออาชีพ ซื่อสัตย์ มีความสุข! ขอบคุณที่ให้บริการและผลิตภัณฑ์ที่มั่นคงแก่ฉัน -----EUROPAT

—— อุตสาหกรรม EUROPT

สนทนาออนไลน์ตอนนี้ฉัน
บริษัท ข่าว
A Complete Guide to Roller Runout on BOPP, BOPET and Cast Film Lines
ข่าว บริษัท ล่าสุดเกี่ยวกับ A Complete Guide to Roller Runout on BOPP, BOPET and Cast Film Lines

A Complete Guide to Roller Runout on BOPP, BOPET and Cast Film Lines

Quick Answer

Runout is the geometric error that a film line cannot compensate for, because it acts on the web once per revolution and therefore cannot be averaged out by any control loop. It originates in journals, shell geometry, bearing fits, thermal distortion and surface build-up, and it is diagnosed most quickly from the repeat length it prints on the film. Correction is a sequence, not a single operation: restore the journals, grind the face to them, generate the surface, then balance — in that order, at the speed and temperature the roll will actually run.

Key Takeaways

· TIR is a composite of roundness, eccentricity, bearing movement and elastic deflection.

· Repeat length = πD; harmonics at πD/2 and πD/3 indicate lobing.

· Film-line rolls are ground to 0.005–0.020 mm TIR against 0.05–0.10 mm as-turned.

· A 400 mm shell can read 0.012 mm at 20 °C and 0.04 mm at 200 °C.

· Balance grade must be quoted with a speed, and balancing must follow the last grind.

· Regrinding removes 0.05–0.15 mm per cycle at 25–40% of new-roll cost.

· Plating and polishing reproduce geometry; grinding generates it.

· In-machine TIR includes the fit, which is why it is the number that matters.

Summary Table: TIR Targets by Duty

Roll duty

TIR target

Typical failure if exceeded

Casting roll, optical or capacitor

≤0.005–0.010 mm

Quench-side gauge band

Chill roll, BOPP and BOPET

0.010–0.015 mm

Contact and heat-transfer variation

MDO preheat and stretch

0.010–0.020 mm

Draw-gap variation

Coating and metering

0.005–0.010 mm

Wet film thickness variation

Idler and guide

0.020–0.050 mm

Tracking and tension disturbance

Winder drum

0.010–0.020 mm

Wound-in bands, starring

 

Knowledge Graph: Previous, Current, Next

Previous: melting, filtration and die delivery set the incoming gauge profile in the Film Industry. A roll cannot correct a die that is already out of profile, which is why gauge faults must be separated from geometry faults before any roll is condemned.

Current: the roll's geometric accuracy — runout, roundness, cylindricity, crown, surface texture — all referenced to the bearing journals and all measured at operating temperature.

Next: quenching on the Casting Roll, drawing between MDO Stretching Roll pairs, cooling on the PRS Cooling Roll and winding. Each stage converts the same geometric error into a different defect, so the same 0.02 mm can be a gauge band at the casting section and a winding defect at the winder.

Part 1: Why the TIR Number Misleads

A dial indicator reports one number, but that number is a vector sum. It contains the roundness error of the measured surface, the offset between that surface and the bearing axis, the radial float permitted by bearing clearance, and the elastic movement of the shell and housing under load.

Two consequences follow. First, two rolls with identical TIR can produce entirely different defects, because the phase and frequency content differ. Second, a roll can fail in production while every component drawing is satisfied, because no single feature is out of tolerance — only the sum is.

Casting and quenching geometry is treated in more depth under Casting Film Rolls. This is why the first question in any investigation should not be "what is the TIR" but "at which angular position, at which axial station, and at what temperature".

Part 2: The Five Error Sources

Source

Signature on the indicator

Diagnostic step

Journal out of round or tapered

TIR differs between stations

Micrometer at two planes on each journal

Shell eccentric to journals

Constant TIR along face, one high point

Compare face and journal readings in one setup

Shell lobed (oval, three-lobe)

Two or three peaks per revolution

Slow rotation with a marked datum

Bearing seat or housing fit

TIR changes with load or after reassembly

Radial clearance and bore measurement

Thermal distortion

TIR grows after warm-up

Cold and hot readings at the same angle

 

Build-up is a sixth source but not a manufacturing one: plate-out, dried coolant solids, polymer film and corrosion all add local thickness. A 0.015 mm deposit reads as 0.015 mm of TIR and is indistinguishable from a machining fault until the surface is cleaned and re-measured.

Part 3: Signature Analysis From the Film

The web advances exactly one circumference per roll revolution when synchronous, so a fixed angular feature contacts the web every πD millimetres.

Diameter

Repeat

Diameter

Repeat

250 mm

785 mm

500 mm

1,571 mm

300 mm

942 mm

600 mm

1,885 mm

400 mm

1,257 mm

800 mm

2,513 mm

450 mm

1,414 mm

1,000 mm

3,142 mm

 

Two corrections make the method dependable. Slip: if the roll runs 2% fast, a true 1,414 mm repeat appears at 1,386 mm or 1,443 mm, so a single measurement can be wrongly dismissed — count across twenty repeats. Harmonics: an oval shell prints at πD/2, a three-lobe shell at πD/3. A repeat at a simple fraction of the circumference moves the diagnosis from surface damage to geometry error, and the repair from polishing to grinding.

For quench-zone specifics, the guide to PRS Cooling Rolls for BOPP, BOPET and BOPA Lines sets out how cooling duty and surface specification interact. The complementary trick is a roll register sorted by circumference. When a defect appears, the repeat length is looked up rather than reasoned about, which turns a multi-day investigation into an afternoon.

Part 4: Measurement Protocol

Stations. Four along the face: drive end, quarter point, centre, far end. A monotonic trend indicates taper or misalignment; a single peak indicates a local defect; two or three peaks indicate lobing.

Datum. Between centres isolates the roll. In the housing includes bearing clearance, bore error and frame deflection. The in-machine number is the one the web experiences, so acceptance should state which datum applies, and a large difference between the two is itself a diagnosis: it is a fit problem, not a grinding problem.

Temperature. The same asymmetry explains the hot–cold gap discussed in the notes on MDO Preheating Rolls for BOPP and BOPET Lines. A 400 mm steel shell with asymmetric internal channels can read 0.012 mm at 20 °C and 0.04 mm at 200 °C. Shells above roughly 300 mm need at least 45 minutes at setpoint. The reading must be recorded with its temperature, or it cannot be compared with anything.

Instrument. A lever-type indicator with 1 µm graduations is adequate for film-line work; resolution is never the limiting factor, access and rigidity are. The mounting must be independent of the roll frame, otherwise frame vibration is measured instead of geometry.

Repeatability. Take two readings per station and rotate the roll back to the same angle for the second. A spread above 2 µm means the setup is not stable enough to judge a 10 µm tolerance.

Part 5: Thermal Distortion

Heated shells distort because the internal channel layout is not thermally symmetric. A spiral channel delivers hotter fluid to one side of the shell before the other, and the resulting gradient bends the shell along its length. The effect is not small: 0.028 mm of apparent runout can appear purely from a temperature difference across the shell.

Three design responses exist. Symmetrical duplex flow, where the fluid enters at the centre and splits in both directions, halves the axial gradient. Peripheral drilling places channels close to the surface and reduces the wall thickness through which the gradient must act. And thermal compensation in the control loop — measuring the shell, not the outlet — keeps the setpoint honest.

Temperature uniformity itself is a separate specification, covered for Bi-Oriented Film Rolls in the stretched-film context. For the operator, the practical rule is that a roll which measures well cold and badly hot has a flow-distribution problem, not a machining problem, and grinding it will remove good material while leaving the error intact.

Part 6: Balance Is a Separate Certificate

ISO 1940 grade G2.5 permits a residual unbalance of about 1.5 g·mm per kilogram of rotor mass. For a 2,000 kg roll that is 3,000 g·mm; the centrifugal force it generates rises with the square of rotational speed, so the same residual matters sixteen times more at 1,200 rpm than at 300 rpm.

Two practical consequences follow. A balance certificate without a quoted speed is not a specification. And balancing must be the last operation, because grinding removes mass — a roll balanced before finish grinding is certified in a condition that no longer exists.

Balance cannot substitute for runout control. A perfectly balanced roll can run out by 0.05 mm and print a clean band; an out-of-round roll can balance to G1.0 and still vibrate the frame.

Part 7: The Correction Sequence

Journals first. Straighten if bent, strip and re-grind if worn, build up and re-machine if undersize. Every subsequent operation references them, so an error here is multiplied downstream.

Face second. Grind the outside diameter concentric to the corrected journals. Correct work support and dress the wheel before the finish passes if lobing is present; a lobed result is almost always a setup fault rather than a wheel fault.

Chrome third. Finishing on the chrome is what makes a BOPP Chill Roll hold gauge at speed. Strip and re-plate where remaining chrome in a loaded zone is below about 0.03 mm, typically to 0.05–0.15 mm at 800–1000 HV, then finish-grind the chrome. The final tolerance is generated on the chrome, not under it.

Crown fourth. Verify crown with impression film under production nip load. Narrow contact at the edges indicates insufficient crown or excessive deflection; narrow contact at the centre indicates over-crown.

Balance last. Two-plane, at maximum operating speed, after the final grind.

Part 8: Acceptance Testing

An acceptance protocol should require the TIR value, the datum, the temperature, all four stations and the angular position of the high point. For heated rolls, cold and hot readings. For all rolls, a balance report quoting grade and speed, a chrome thickness measurement, and roundness and cylindricity reported separately from TIR.

Converters handling coated or metalised structures should extend the same logic to their Film Converting Rolls, where a metering roll error becomes a wet-film error directly. The most common gap in purchase specifications is a TIR value with no method attached. Two suppliers can both claim 0.01 mm and deliver rolls that behave completely differently, because one measured between centres cold and the other measured in the housing hot.

Failure Analysis

Symptom

Measurement

Cause

Action

ผับเวลา : 2026-11-18 16:58:45 >> รายการข่าว
รายละเอียดการติดต่อ
TOGETHER HTL LTD

ผู้ติดต่อ: Mr. Maple

โทร: +86 17778255675

แฟกซ์: 86--311-80690567

ส่งคำถามของคุณกับเราโดยตรง (0 / 3000)